LinkBack URL
About LinkBacks
Reply With Quotebumpity bump
|
|
|
This is a discussion on AirLift Helper Bags, Belltech C-Notch within the Suspension / Brakes forums, part of the For-Sale category; They are the AirLift Slam-Air kit thats for 4"-6" REAR DROP for OBS. The part # is 59106BT. It is ...
They are the AirLift Slam-Air kit thats for 4"-6" REAR DROP for OBS. The part # is 59106BT. It is designed to bolt to Belltech C-notch. Everything needed to install will be included except nuts and bolts to bolt to notch. The (2) pieces of airline that are included, are long enough to run from the gass door to each bag for SWB. Both bags have a light wear mark in them from a brake line that was rubbing, but holds air just fine. Less than 6 months old. $100 shipped obo.
25 psi, they will hold up to 100psi but it says not to air up unless installed, soo....
the rub marks
installed
OBS Belltech Bolt-in C-Notch was in the truck for a little over a year. The top is notched so you don't have to take the bed off to install. In great shape, just never cleaned them after i took them off, will clean up before shipping. $70 shipped
Last edited by drpdshrty; 06-03-2007 at 01:24 PM.
Drew Huckins, Wichita, Kansas
1994 Chevy
5/8 Belltech
15x7, 15x10 Weld Split 6
bumpity bump
Drew Huckins, Wichita, Kansas
1994 Chevy
5/8 Belltech
15x7, 15x10 Weld Split 6
hey ill take those notches.
they are yours, I take paypal, drpdshrty@aol.com
Drew Huckins, Wichita, Kansas
1994 Chevy
5/8 Belltech
15x7, 15x10 Weld Split 6
bump.....all is still for sale
Drew Huckins, Wichita, Kansas
1994 Chevy
5/8 Belltech
15x7, 15x10 Weld Split 6
i was wondering will those bags work on a 2000 silvy?? thanks
1979 Scottsdale, Edelbrock 650 with offroad needles and seats, edelbrock performer intake, 4in lift, 33-10.50-15 bfg a/t, 2.5" duals, Flowy 44's
Coming Soon:??
well they are made to bolt to a Belltech c-notch for 88-98. Also they are made for a 4-6" rear drop. if your truck is lowered, im sure you could just drill holes in the frame to mout the upper bracket.
Drew Huckins, Wichita, Kansas
1994 Chevy
5/8 Belltech
15x7, 15x10 Weld Split 6
got email
never recieved any email from you
Drew Huckins, Wichita, Kansas
1994 Chevy
5/8 Belltech
15x7, 15x10 Weld Split 6
Originally Posted by drpdshrty
NiceSend through forum.......
Just a question, would you send to Germany? Should be possible by usps ... If yes, just contact me by pm!
best regards
Felix
PM sent on the bags. Money in hand.
Status on the bags? I would like 'em if they are still available.
i havent heard from either of these guys so they are yours if you'd like them. i take paypal drpdshrty@aol.com. Unless you want to come get them. $70 if you pick them up.
Drew
Drew Huckins, Wichita, Kansas
1994 Chevy
5/8 Belltech
15x7, 15x10 Weld Split 6
With gas prices the way they are, I don't think driving to Wichita will be less than $30. I think we would be better off shipping them! Thanks for the offer though
Did you have any problems airing them up with a load? I have airshocks right now and the ride sucks...I want to add a set of good shocks but still be able to level the truck out when I haul or tow something. Plus you can't really add air to the shocks after the load is already in the bed.
Could you send a closer picture of the upper bracket? I don't have bell tech c-notches, but I think they'll do.
This is what I have-
Surely I can get them to work. I'll wait to send the money until I can get a closer look at the bracket...unless you think they will bolt up.
How much do you think shipping would be? Give me a final price when you send the pic...
Thanks
Derek
Email sent on the bags...
Founder Muscle Syndicate.com
The Up and Coming Muscle Car Club
D-Bob- I always aired the bags up when i was going to be hauling something heavy, or just to change the stance a little, lol. they hold up to 100psi, but 70psi is the most i ever needed to put in them. The ride was really nice actually with athem aired up.
I'm pretty sure that it will work, im just not sure of the distance between the bolts on your notch. if it doesnt bolt up, you would just have to drill new holes. here is a pic of the upper bracket.
The distance bewteen the hole, up and down, is 2 3/4" center to center, and side to side, 4 1/2" center to center.
I posted the price of $100 shipped in the original post so ill stick with that.
Let me know if you have anymore questions.
Drew
Drew Huckins, Wichita, Kansas
1994 Chevy
5/8 Belltech
15x7, 15x10 Weld Split 6
here is a picture of my notch. looks like the bolt pattern of our notches are a little different
Drew Huckins, Wichita, Kansas
1994 Chevy
5/8 Belltech
15x7, 15x10 Weld Split 6
Yeah, see I measured last night and my bolt holes are only about 2 1/2" apart, whereas yours are 4 1/2". No big deal...I know people who can weld :LOL:
I can just weld a piece of angle to the bracket and drill my holes through that. Money will be sent for them today!
Thanks
Last edited by D-BoB'91; 07-10-2007 at 02:17 PM.
Hey Drew,
Tried to PM you but you didn't have room to accept any more messages. :LOL:
Do you still have the hidden hitch for OBS? I saw it in your other post. If it's the one to use with a roll pan, I will go ahead and make the trip up there for the bags and hitch. Let me know.
Thanks,
Derek
Hey man I had some crap with the National Guard come up and I just got back. Can I still send you the money for those bags or are they already gone?
Posting Permissions
 |
Bookmarks