Announcement

Collapse
No announcement yet.

Camshaft Position Sensor

Collapse

Unconfigured Ad Widget

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Camshaft Position Sensor

    The trucks been getting harder to start for the last week or so, so I had the codes ran today. Through a P0340, Camshaft Position Sensor A- Bank 1 Circuit Malfunction.

    I searched around the forums and dint really find much besides that the CPS is located somewhere below the distributor.

    How would I approach changing this? is it hard? Or is it just unscrewing and unplugging the old one and throwing the new one in?
    What would be the esiest way to access it? From under the truck? Or from the top?

    Help!!!
    1998 Chevy K1500- Used, Abused, and Sold 1989 Camaro Iroc-Z 5.0, auto....- Sold
    1987 Dodge Dakota 2bbl, 5 spd, v6, 4x4, -scrap
    1993 Honda CBR600 F2- DD when nice out 1987 k5 blazer- bad ass

  • #2
    Re: Camshaft Position Sensor

    ttt
    1998 Chevy K1500- Used, Abused, and Sold 1989 Camaro Iroc-Z 5.0, auto....- Sold
    1987 Dodge Dakota 2bbl, 5 spd, v6, 4x4, -scrap
    1993 Honda CBR600 F2- DD when nice out 1987 k5 blazer- bad ass

    Comment


    • #3
      Re: Camshaft Position Sensor

      The CPS is inside the distributor cap housing. You'll need to take the cap off. Remove the rotor and you'll see it on the backside towards the firewall. There should be two little torx head screws holding it in place. Be careful not to drop the screws inside the distributor. Unplug the harness. You shouldn't have any problems. I can't remember, but it may need some di-electric grease upon reinstallation of the new one??? Anyone else know this bit of info?

      Have you tried jiggling the wiring harness yet? I'm assuming not since you didn't know the exact location of it. Try to move the harness a bit and see if it will start. I had one do this once before. Also would get moisture in when it was wet outside due to the bad connection. Just a thought.
      1997 C1500 ECLB 5.7 Vortec G80 3.73 Rear
      K&N FIPK, Cherrybomb Vortex DI/DO Dumped

      Comment


      • #4
        Re: Camshaft Position Sensor

        Originally posted by JJonesey
        The CPS is inside the distributor cap housing. You'll need to take the cap off. Remove the rotor and you'll see it on the backside towards the firewall. There should be two little torx head screws holding it in place. Be careful not to drop the screws inside the distributor. Unplug the harness. You shouldn't have any problems. I can't remember, but it may need some di-electric grease upon reinstallation of the new one??? Anyone else know this bit of info?

        Have you tried jiggling the wiring harness yet? I'm assuming not since you didn't know the exact location of it. Try to move the harness a bit and see if it will start. I had one do this once before. Also would get moisture in when it was wet outside due to the bad connection. Just a thought.
        Thank you very much! Thats just the info I was looking for.
        1998 Chevy K1500- Used, Abused, and Sold 1989 Camaro Iroc-Z 5.0, auto....- Sold
        1987 Dodge Dakota 2bbl, 5 spd, v6, 4x4, -scrap
        1993 Honda CBR600 F2- DD when nice out 1987 k5 blazer- bad ass

        Comment


        • #5
          Re: Camshaft Position Sensor

          Could be the circuit to and from the sensor as well.

          peace
          PAuly
          97 GMC 2wd RCSB 5.7, s10 2700 footstall, Hooker 24621hkr LT's , 2.5" cats dual 4"pipes exit B4 pass. side tire, custom driveshaft 3.42 G80 FIPK MAF descreen GM/Mercruiser Marine intake manifold 29lb LS2(EV6) injectors Ed Wright PCM(best mod), LT4 KM 14.8@94mph 2.007 4000lbs 122mph

          Comment


          • #6
            Re: Camshaft Position Sensor

            Just replaced the sensor... Still doesnt start. I guess Pauly was right. I dont know what I'm going to do now, no idea where the circut goes...
            1998 Chevy K1500- Used, Abused, and Sold 1989 Camaro Iroc-Z 5.0, auto....- Sold
            1987 Dodge Dakota 2bbl, 5 spd, v6, 4x4, -scrap
            1993 Honda CBR600 F2- DD when nice out 1987 k5 blazer- bad ass

            Comment


            • #7
              Re: Camshaft Position Sensor

              The pink wire at the sensor should have power with the key on. The other two wires go to the VCM. On the 96(I dont have a 98 service manual) they went to the blue connector, posts 3 and 8 but matching the wire colors at the sensor and vcm should work

              Comment


              • #8
                Re: Camshaft Position Sensor

                Had a similar problem. A voltmeter is your friend.
                97 Gmc Sierra 1500
                Current mods: Flowmaster 40's, K&N FIPK, S10 converter, wait4me tune, LT1 fans, 2" drop shackles, Alpine CDA-9856 head unit.

                Comment

                Working...
                X