View Full Version : Dash Upgrade Wiring Information


cordatta
04-06-2007, 01:12 AM
So I have decided to do the dash swap and after looking over Wiring Schematics for a 1998 Dash have come up with the following information concerning the Steering Column. The information presented here is the work of my current status and thought I would share the information with everyone here. Though the list is incomplete I will continue to update the information as time allows. I claim no responsibilty of the accuracy of this information and have yet to perform the swap so read and use at your own risk. Information provided below is from Mitchell CD's that I have bought and traced out via about 60pages of diagrams. The XXXXXXX that you see indicate that no wires are present on the Connectors that I have. Enjoy.

1998 Chevy C1500 Steering Column Connectors

Multifunction Switch (2 Connectors; Grey and Black)
Gray P.E.D. 8
E1 Lgt Green - Grey on schematic - Hazard/Turn Switch goes to Hazard Power
2 White - Lgt Blue on schematic - Hazard/Turn Switch goes to Stop Lamp Relay
3 Purple - goes to Hi on Wiper Motor
4 Yellow - Wiper Switch (Hot in Accessory)
5 Grey - Brown on schematic - goes to Low on Wiper Motor
6 Dk Green - Hazard/Turn Switch goes to Right Rear Tailight
7 Yellow - Hazard/Turn Switch goes to Left Rear Tailight
8 Orange - Hazard/Turn Switch goes from Stop Lamp Switch (Always Hot)
9 Purple - Hazard/Turn Switch goes to Flasher Out
10 XXXXXXXX
11 Lgt Green -
12 Tan -
E13 Lgt Blue -

Black
D-8-67 Delco Remy P.E.D. 4
A 1 White - Stop Lamp Switch goes to Orange (Always Hot)
2 Pink - Hazard/Turn Switch goes to (Hot in Run Position)
3 Lgt Blue - Hazard/Turn Switch goes to Turn Power
4 XXXXXXXX XXXXXXXX
5 XXXXXXXX XXXXXXXX
6 Dk Blue - Hazard/Turn Switch goes to #32 on Instrument Cluster then goes to Left Parking Lamp
7 Lgt Blue - Hazard/Turn Switch goes to #3 on Instrument Cluster then goes to Right Parking Lamp
8 XXXXXXXX XXXXXXXX
9 XXXXXXXX XXXXXXXX
10 XXXXXXXX XXXXXXXX
11 Black -
12 Grey - Cruise On Input
13 Pink - (Hot in Run)
14 Dk Blue - Set Cruise Input
15 Grey/Black - Resume/Accel Input
16 Black - Electrical BTSI Actuator
A 17 Green/White - Electrical BTSI Actuator goes to Top of Brake Pedal


Square Black P.E.D. 12
D C B
1 Yellow White XXXXXXXX 1
2 Red Black/Grey Black 2
3 XXXXXXXX Grey Green 3
4 Lgt Blue Orange/Black Brown (Dk ?) 4
5 Red/White Pink Tan/White 5
6 Brown Orange XXXXXXXX 6
D C B

D1 Yellow - Ignition Switch goes to Passlock Sensor goes to Passlock Module - to Park/Neutral from Fuse Block
D2 Red -
D3 XXXXXXXX
D4 Lgt Blue - EVO - Steering Handwheel Sensor
D5 Red/White - Ignition Switch goes to Passlock Signal goes to Passlock Module
D6 Brown - Fuse Block for Wipers

C1 White - Fuse Block to Transmission Controls and Instrument Cluster
C2 Black/Grey -
C3 Grey - EVO - Steering Handwheel Sensor
C4 Orange/Black - EVO - Steering Handwheel Sensor
C5 Pink - Power Distribution Center Figures #2 & #3 out of 5
C6 Orange -

B1 XXXXXXXX
B2 Black -
B3 Green -
B4 Brown (Dk?) -
B5 Tan/White - From Ignition Switch to Daytime Running Module
B6 XXXXXXXX

99-2door
04-06-2007, 01:24 AM
If any body needs pin outs like that, ask me. I can get them for every connector in the vehicle. I would be happy to send them to you if you need them. No need to wade through tons of diagrams.

cordatta
04-06-2007, 01:31 AM
wow that would be most excellent. anyway you could send me say pin outs for 1993 1996 and 1998 Chevy? I have a 1993 I am performing this swap on but I have a 95-96 dash and a 98 steering column. Not sure if the diagrams are different from the 95-96 dash to the 98 column. thanks man. email is coot13@sbcglobal.net

99-2door
04-06-2007, 03:27 AM
wow that would be most excellent. anyway you could send me say pin outs for 1993 1996 and 1998 Chevy? I have a 1993 I am performing this swap on but I have a 95-96 dash and a 98 steering column. Not sure if the diagrams are different from the 95-96 dash to the 98 column. thanks man. email is coot13@sbcglobal.net

Which connectors specifically?

mrteacha
04-06-2007, 07:26 PM
im doing the 99 panels on my 92 i could use write up for the door harness/plug. i want to make a plug and play adapter. i would keep my 92 plug inmy kick use the 95+ plug from the door skns and mate the adapter using a donor 92 plug with a donor 95+ plug. what i could use from you is the wire color and is use for both the 92 and 95+ door panel harnesses..thanx