lots of 10 bolt stuff!!!

[K5Chris]

2 sets of 4.56 gears 8.5": SOLD
30 spline Auburn LSD: 170
30 spline open diff: 30
2 sets of 6 lug 30 spline rear axle shafts: 40 per pair
disc brakes complete: SOLD
Spicer 1310 yoke: 10
Saginaw S44 yoke: 10
2 rear stock diff covers: 5 each
stock half ton spring plates (for ubolt flip): 15
half ton u-bolts for 4-5.5" blocks... SOLD
2.5" cast iron lift blocks: 15
adjustable traction bars; go above leafs; prevents axle wrap; sells in jc whittney for 80 bucks: yours for 25

also have 2 rear housings, but i doubt they are worth picking up.

pics available upon request
located in houston texas
prices do not include shipping
i'm open to offers/trades i need a 600-700 watt mono amp, could use some offroad/auxillary lighting, power inverter, alarm, msd ignition.... whatever, let me know what you got.

[dapolice1]

I guess the Yokes will fit the 8.5" 10 bolts in the 88-98 trucks?
I know your a 73-85 kinda guy and I am not sure if there is a diffrence in the rears. I know there are some.. I am intreasted in the spicer

[SLMDLT1]

Let me know what the disc brake setup looks like and I will probably take it.

[K5Chris]

Let me know what the disc brake setup looks like and I will probably take it.

i almost forgot, the rotos i have are 6 lug. you might be able to find 5 lug rotors with a center hole big enough to fit the axle flange. maybe dodge or ford 4wd front rotors.

the calipers and pads are from 84-86 Ford Mustang SVO, contintental, or mark IV. they are rear calipers so they are set up for ebrake, but they are missing the actuating arms. you might be able to find some at a junkyard or find someone who can fabricate them. i reciently rebuilt the calipers, had the rotors resurfaced, and put new pads on them. pads probably have about 75% left. i ran these with no modifications to my combination/porportining valve, and it stopped great, never gave me problems.

[K5Chris]

I guess the Yokes will fit the 8.5" 10 bolts in the 88-98 trucks?
I know your a 73-85 kinda guy and I am not sure if there is a diffrence in the rears. I know there are some.. I am intreasted in the spicer

everything should be the same. i think i decided i wanna hang onto that one for later on.

[1buda]

PM sent.

[K5Chris]

forgot to mention, the traction bars will probably only work with 52" rear leafs. they might work with 56 inchers, but i doubt theyd be long enough to fit on 63's.

[dumpedv8]

do you know off hand if those 4.56 would fit into an 99-04' rear. 10 bolt, i believe 8.5?

[dapolice1]

the 1350 u joints are the heavy duty ones right? the 1310 are standard duty aren't they?

[K5Chris]

do you know off hand if those 4.56 would fit into an 99-04' rear. 10 bolt, i believe 8.5?

the gears are for an 8.5" diff. so, if it's 8.5", they will fit. i have no idea about the 8.6" diffs..... i heard they will, but i dont know for sure.

[K5Chris]

the 1350 u joints are the heavy duty ones right? the 1310 are standard duty aren't they?

the 1310 spicer/ S44 saginaw size is standard on half tons, i believe they've been only using the S44 style on the rears for a while.
the 1350 spicer size is a 3/4 to 1 ton ujoint. it's a bigun.
if you still have a half ton driveshaft, you will have to use the conversion ujoint, part number: 447 .......it has the Saginaw S44 style for the driveshaft, and the 1350 spicer style for the yoke. (which really isnt much stronger - if you want a stout driveline, you'll have to get a new driveshaft)

[dapolice1]

PM sent lets make a deal..

[4wheelin69]

Hey chris can I get the 2in blocks, Do they come with the u-bolts to?

thanks

[96tahoe2door]

with the abs work with the brakes???

[96redsportside]

forgot to mention, the traction bars will probably only work with 52" rear leafs. they might work with 56 inchers, but i doubt theyd be long enough to fit on 63's.

How do I figure out how how long my leafs are? Also, how well do these work, are they worth it on a stock truck?

[K5Chris]

Hey chris can I get the 2in blocks, Do they come with the u-bolts to?

thanks

ubolts should never be reused. i actually had to cut them off.
gimmie your zip and ill see what shippings gonna run.

they are 2.5", and they have a very very slight taper to them, i think.

[K5Chris]

with the abs work with the brakes???

87-95 - YES

96+ - im not sure. are there abs sensors at each wheel?

[K5Chris]

How do I figure out how how long my leafs are? Also, how well do these work, are they worth it on a stock truck?

the 88-98 bodystyle half tons should all be 63 inchers. i couldnt tell ya if they work or not, i never used em.

[4wheelin69]

My zip 79412

[1buda]

Can you get me shipping to zip 15066 on the traction bars and possibly a picture I still might be interested.

Thanks

[Scion]

Interested in the blocks also. Shipping to 87111?

[K5Chris]

here's the traction bars. they are basically 3 pieces. one piece bolts to the front spring hanger, one bolts to the ubolts, and the bar goes between those 2 pieces. the bars are about 25.5 inches long. so, measure from the back of your rear spring front hanger to somewhere in the middle of your ubolts.

it's not installed, i just put it on my truck to show you how it works.

http://memimage.cardomain.net/member_img_a/383211_109_full.jpg
http://memimage.cardomain.net/member_img_a/383211_110_full.jpg
http://memimage.cardomain.net/member_img_a/383211_112_full.jpg

[LS6TT]

what is all included with the rear brakes? caliaper, rotors, lines, brackets?
this is a bolt up, as in can i install it on my c1500 (given i will find a 5 lug rotor

[1buda]

K5Chris thanks for the pictures
Traction bars will not work on my project.

[K5Chris]

what is all included with the rear brakes? caliaper, rotors, lines, brackets?
this is a bolt up, as in can i install it on my c1500 (given i will find a 5 lug rotor

everything. i pulled them off my truck which is driven daily, and everything is included.

it uses front rotors from an 88 1/2 ton 4wd
calipers, pads, and caliper brackets are from the rear of 84-86 mustang SVO.
the mustang brackets are bolted to custom cut plate steel brackets.
also has dust shields, and flex hoses to connect to your hard line.

it has everything you need for hydraulic braking, if you want ebrake, it's missing arms that acuate the ebrake, and the bracket on one side that holds the ebrake cable.

http://memimage.cardomain.net/member_img_a/383211_113_full.jpg

[Hiper Z]

K5Chris, I will take the rear disc brakes. email me. bigcountrycustom@aol.com

Mark

[LS6TT]

so could i use front brakes from a c1500? since its using fronts from a k1500?
whats a total on shipping to 76039

[K5Chris]

K5Chris, I will take the rear disc brakes. email me. bigcountrycustom@aol.com

Mark

i have one person interested in front of you, i will definately let you know if it doesnt work out.

[K5Chris]

so could i use front brakes from a c1500? since its using fronts from a k1500?
whats a total on shipping to 76039

no. the center hole (if there is one - trying to remember) on the 2wd rotor is not nearly big enough to fit over the axle flange. (the 4wd rotors even have to be machined a little to fit the axle shafts) ford or dodge 4wd front rotors might work. they are 5 lug.

[K5Chris]

here's the gears. great shape, no rust no pitting. i wouldn't post extreme close pictures if they weren't in great shape.

http://memimage.cardomain.net/member_img_a/383211_116_full.jpg
http://memimage.cardomain.net/member_img_a/383211_114_full.jpg
http://memimage.cardomain.net/member_img_a/383211_115_full.jpg

[LS6TT]

no. the center hole (if there is one - trying to remember) on the 2wd rotor is not nearly big enough to fit over the axle flange. (the 4wd rotors even have to be machined a little to fit the axle shafts) ford or dodge 4wd front rotors might work. they are 5 lug.

ok thats cool, well whats the cost of shipping to 76039

[K5Chris]

Ttt

[K5Chris]

TTT

4.56 gears and ubolts are sold

everything else needs to go. i will consider trades. the stuff i need is in the original post. but, i need a 600-700 watt mono amp the most.

[K5Chris]

ttt

disc brakes sold

[Regal1]

how many miles on the auburn? what kind of condition is it in? pics of it?