|
|
03-03-2008, 01:45 AM
|
#1 |
|
Premium Member #20
Forum Leader
Status: Offline
Join Date: Jul 2003
Member ID: 7196
Pics: My Gallery
Location: CA
Age: 23
Posts: 5,114
|
RnuovZ71 SAS build
I have finaly collected most of the parts I needed to start the SAS on my 92 ECSB Chevy. This next week I will be getting my springs in along with all the stuff for my hydro steering. Tomorrow I'm going to order my detriot lockers and 4.56s front and rear. it should be 9" in front and 8" in the back.
What I would like to have done still Is get the bed sprayed w/ rhino liner(or the like), I would also like the have the quarter panels rhino lined. Then I need a new motor. The list goes on with odds and ends, but It will slowly come along. This is the list of stuff I have so far... 78 dana 60 kingpin front. 87 dana 70 rear. ORU SAS kit +6" in spring length. 16x10 cast black procomp rims. Kingpin rebuild kit. New pads/ shoes for the brakes. new ujoints for the axle shafts. 37x13.50 mickey thompson Baja Claws. 4.56s Front & Rear. Detriot lockers F/R. Hydro steering stuff. Draglink. Steering arm. Tie rods. Brake lines. Hub Bearings. Ubots and Ubolt plates. Ujoint rear axle. List of stuff I still need... Front driveline. Shocks. Time, time, time and more time. I know I'm forgetting a few things but oh well... BTW the stock gears and carriers out of the front and rear axles need to go. The D60 front has/had 4.10 I think 50+ shipping is fair. The D70 Rear has/had 3.73s 50+ shipping. The stock 3.73 from the 10 bolt rear and front, I need to get rid of also. I need some room here in my shop, If there is anything you need PM me I may have it.   1992 ECSB SFA K1500: D60 Front, D70 Rear, Hydro assist. 9"s of lift sittin' on 37"s 1997 RCSB K1500: CAI, Exhaust, Tune. Headed to the trans shop! 1999 2dr Tahoe: 4" Rancho Lift, 4.56s W/ True-trac. Last edited by RnuovZ71 : 06-12-2008 at 08:10 PM. |
|
|
03-03-2008, 08:24 AM
|
#2 | ||
|
Premium Member #3
Push the needle in
 Status: Offline
Join Date: Nov 2004
Member ID: 20736
Pics: My Gallery
Location: NJ
Age: 33
Posts: 931
|
Re: RnuovZ71 SAS build
Quote:
Are those teflon? they look good, should be easy to clean also.  Tooned by Lowdown '98 K1500 DC 6.5" Stage II, RC torsion bars, 7" Alcans, 4.56's, 35" Nitto MG, Black DC-1's, Black Bear Performance Tune '07 Trailblazer 3SS AWD Quote:
|
||
|
|
|
03-04-2008, 03:37 PM
|
#3 |
|
Premium Member #20
Forum Leader
Status: Offline
Join Date: Jul 2003
Member ID: 7196
Pics: My Gallery
Location: CA
Age: 23
Posts: 5,114
|
Re: RnuovZ71 SAS build
The lockers and 4.56s with be here tomorrow (wed). My hydro stuff should be here fri. The damned spring will be here next week.
I have more pics to upload. 1992 ECSB SFA K1500: D60 Front, D70 Rear, Hydro assist. 9"s of lift sittin' on 37"s 1997 RCSB K1500: CAI, Exhaust, Tune. Headed to the trans shop! 1999 2dr Tahoe: 4" Rancho Lift, 4.56s W/ True-trac. Last edited by RnuovZ71 : 03-04-2008 at 03:38 PM. |
|
|
|
03-04-2008, 03:40 PM
|
#4 | |
|
Premium Member #20
Forum Leader
Status: Offline
Join Date: Jul 2003
Member ID: 7196
Pics: My Gallery
Location: CA
Age: 23
Posts: 5,114
|
Re: RnuovZ71 SAS build
Quote:
They're cast black with a teflon coating. BTW I hope so 1992 ECSB SFA K1500: D60 Front, D70 Rear, Hydro assist. 9"s of lift sittin' on 37"s 1997 RCSB K1500: CAI, Exhaust, Tune. Headed to the trans shop! 1999 2dr Tahoe: 4" Rancho Lift, 4.56s W/ True-trac. |
|
|
|
|
03-04-2008, 04:48 PM
|
#5 |
|
Registered User
Status: Offline
Join Date: Jan 2006
Member ID: 41306
Pics: My Gallery
Location: Minnesota
Posts: 354
|
Re: RnuovZ71 SAS build
cool project
layin on 22s
 98 cherokee 3in lift with 31in ss ltb, 93 gmc siera layed on 22s thanks to 97Bowtie1106 for the sig |
|
|
|
03-05-2008, 04:26 PM
|
#6 |
|
MUD TOY
Status: Offline
Join Date: Mar 2007
Member ID: 65325
Pics: My Gallery
Location: Bay City . MI
Age: 36
Posts: 104
|
Re: RnuovZ71 SAS build
Can't wait to see more. looks like parts pile is growing!
94 Yukon SAS 9" total lift, 4.56 Gears, 14 bolt Detroit locker rear,3/4 ton 10 bolt truetrac locker front,396BB 60 over, 750 holly double pumper,400TH,3000 stall conv,NP203,35s 16 wide boggers
|
|
|
|
03-05-2008, 06:33 PM
|
#7 | |
|
Premium Member #20
Forum Leader
Status: Offline
Join Date: Jul 2003
Member ID: 7196
Pics: My Gallery
Location: CA
Age: 23
Posts: 5,114
|
Re: RnuovZ71 SAS build
Quote:
Oh it is. I cant wait to have it done just the way I want it. here is one teazer pic of the D70 gears, I have more pics tonight...  1992 ECSB SFA K1500: D60 Front, D70 Rear, Hydro assist. 9"s of lift sittin' on 37"s 1997 RCSB K1500: CAI, Exhaust, Tune. Headed to the trans shop! 1999 2dr Tahoe: 4" Rancho Lift, 4.56s W/ True-trac. |
|
|
|
|
03-06-2008, 01:36 PM
|
#8 |
|
Premium Member #20
Forum Leader
Status: Offline
Join Date: Jul 2003
Member ID: 7196
Pics: My Gallery
Location: CA
Age: 23
Posts: 5,114
|
Re: RnuovZ71 SAS build
Like I said MORE pics of the stuff in my shop...
I have to get better pics, the ones I uploaded look like ass. But here are a few... The rims  The rear d70  The front d60                 1992 ECSB SFA K1500: D60 Front, D70 Rear, Hydro assist. 9"s of lift sittin' on 37"s 1997 RCSB K1500: CAI, Exhaust, Tune. Headed to the trans shop! 1999 2dr Tahoe: 4" Rancho Lift, 4.56s W/ True-trac. Last edited by RnuovZ71 : 03-07-2008 at 04:25 PM. |
|
|
|
03-06-2008, 09:47 PM
|
#9 |
|
Registered User
Status: Offline
Join Date: Jun 2005
Member ID: 30029
Pics: My Gallery
Location: indiana
Age: 19
Posts: 124
|
Re: RnuovZ71 SAS build
So whenever you feel like it you can box up that old lift and send it to my house.
|
|
|
|
03-07-2008, 04:24 PM
|
#10 |
|
Premium Member #20
Forum Leader
Status: Offline
Join Date: Jul 2003
Member ID: 7196
Pics: My Gallery
Location: CA
Age: 23
Posts: 5,114
|
Re: RnuovZ71 SAS build
All my hydro assit stuff came in today(i'll get pics later). How ever I need to go and get a rebuild kit for the PS gear box/ find and rebuild a 2wd gear box so I can get a drop pitman arm.
I'm still waiting on my springs. A frind of mine is going to show/ teach me how to set gears. So I can get the rear D70 in place(I may even do a shackle flip). Then I need to remove the BL and ALL spacers. I still need to clean out the in part of the axle B4 I set the gears and set in new seals. So I hoping for a productive week end. 1992 ECSB SFA K1500: D60 Front, D70 Rear, Hydro assist. 9"s of lift sittin' on 37"s 1997 RCSB K1500: CAI, Exhaust, Tune. Headed to the trans shop! 1999 2dr Tahoe: 4" Rancho Lift, 4.56s W/ True-trac. |
|
|
|
03-07-2008, 08:00 PM
|
#11 |
|
Registered User
Status: Offline
Join Date: Dec 2006
Member ID: 60251
Pics: My Gallery
Location: Athens, GA
Posts: 499
|
Re: RnuovZ71 SAS build
looks like a great build. subscribed
'99 Sierra 1500 4x4 Z71. 90* Flowmasters, 285 M/T 10" Alpine
Go Dawgs! |
|
|
|
03-07-2008, 08:04 PM
|
#12 |
|
Premium Member #123
i hate rust!!
Status: Offline
Join Date: Jun 2005
Member ID: 30152
Pics: My Gallery
Location: Leominster MA
Age: 31
Posts: 551
|
Re: RnuovZ71 SAS build
subscribed
|
|
|
|
03-08-2008, 03:06 PM
|
#13 |
|
Premium Member #20
Forum Leader
Status: Offline
Join Date: Jul 2003
Member ID: 7196
Pics: My Gallery
Location: CA
Age: 23
Posts: 5,114
|
Re: RnuovZ71 SAS build
Crap, I ran into a little snag. when I ordered my springs I told the guy go head and run my card. So this intire time I thought I prepaid and come to find out they wherent. I guess the guy didnt do it. So now I have to wait till my next pay check to get them.
And I dont get paid untill the 15. Oh well looks like it will only slow me for 2 weeks. I am going to however get EVERYTHING ready for when the spring get here I can just get everything mounted. 1992 ECSB SFA K1500: D60 Front, D70 Rear, Hydro assist. 9"s of lift sittin' on 37"s 1997 RCSB K1500: CAI, Exhaust, Tune. Headed to the trans shop! 1999 2dr Tahoe: 4" Rancho Lift, 4.56s W/ True-trac. |
|
|
|
03-08-2008, 03:16 PM
|
#14 |
|
Chevy's For Life
Status: Offline
Join Date: Jan 2007
Member ID: 61697
Pics: My Gallery
Location: Kansas City
Age: 21
Posts: 518
|
Re: RnuovZ71 SAS build
Are you selling the old lift kit
 Sig by: 454ss  __/_|___ [O___O_]..":..* ; <- haha internet sparks 1988 Chevy RCLB K2500 4x4-Mud Toy-Died Sold 1980 Chevy SWB C10-For Sale 1979 Chevy SCLB C20 |
|
|
|
03-08-2008, 03:24 PM
|
#15 | |
|
Can I Hab Some?
Status: Offline
Join Date: Aug 2006
Member ID: 53530
Pics: My Gallery
Location: Halifax, Nova Scotia
Age: 23
Posts: 2,127
|
Re: RnuovZ71 SAS build
Nice pile of parts, which equates to a nice chunk of change
 Good to see the SAS underway though and good luck. Subscribed  <-Thanks Chuggs   Quote:
|
|
|
|
|
03-08-2008, 04:11 PM
|
#16 | ||
|
Premium Member #20
Forum Leader
Status: Offline
Join Date: Jul 2003
Member ID: 7196
Pics: My Gallery
Location: CA
Age: 23
Posts: 5,114
|
Re: RnuovZ71 SAS build
Quote:
I have a sale pending Quote:
Thanks, and yea I have about 4000 dollars worth of Parts in my shop. I still have a little  ing to do to the truck but thats all minor stuff.1992 ECSB SFA K1500: D60 Front, D70 Rear, Hydro assist. 9"s of lift sittin' on 37"s 1997 RCSB K1500: CAI, Exhaust, Tune. Headed to the trans shop! 1999 2dr Tahoe: 4" Rancho Lift, 4.56s W/ True-trac. |
||
|
|
|
03-09-2008, 10:46 AM
|
#17 |
|
Registered User
Status: Offline
Join Date: Nov 2004
Member ID: 20738
Pics: My Gallery
Location: Bridgeport/wv
Age: 22
Posts: 40
|
Re: RnuovZ71 SAS build
looks like its slowly coming along subscribed
|
|
|
|
03-09-2008, 11:34 AM
|
#18 |
|
No more F'n Bailouts!
 Status: Offline
Join Date: Feb 2002
Member ID: 1089
Pics: My Gallery
Location: Honolulu, Hawaii
Age: 42
Posts: 14,996
|
Re: RnuovZ71 SAS build
    You get what you pay for......nothing is free. |
|
|
|
03-09-2008, 02:13 PM
|
#19 |
|
Redneck
Status: Offline
Join Date: Jun 2005
Member ID: 29014
Pics: My Gallery
Location: Hudson, WI
Age: 20
Posts: 2,547
|
Re: RnuovZ71 SAS build
looking good
 2004 Chevy Silverado ECSB Z-71-----LOUD PIPES...SAVE LIVES D.F.W.A NEW RIDE http://www.cardomain.com/ride/2595281/1 TRADED http://www.cardomain.com/ride/2300960 |
|
|
|
03-09-2008, 02:28 PM
|
#20 |
|
FSC Drunkin Teem
Status: Offline
Join Date: Aug 2002
Member ID: 2427
Pics: My Gallery
Location: Hooks, Texas...i keep working closer and closer to 'Bama!
Age: 25
Posts: 2,934
|
Re: RnuovZ71 SAS build
oh hell yea man! this is a build i've been lookin forward to for a bit...can't wait to see it done...good luck with it all!
 <---thanks 454SS!!1991 Chevy Silverado K1500 extended cab, 350, 700R4 with shift kit, exhaust work...in need of body work...lol... 1983 GMC Sierra K1500 sold... 
|
|
|
Linear Mode
